Search results

Nearly had the beans all over the table haha. I rarely go to a greasy spoon but this was awesome, massive plate of filth I hope its of use to people in the future ? Cheers mate, i have some clear side repeaters and some headlamps off the last of this shape kangoo with clear indicators...

Cup looks great, well worth the money ?

Weekend update Refitted later 172 ecu/uch and fired engine up from cold - idled normal and settled down to 800ish rpm idle when hot. I scanned it with clip and a load of old faults were stored relating to ct temp sensor etc assuming off the old car - cleared them and no furthur idle issues -...

Good to hear its sorted - nothing worse than unwanted lights on ! i knew it wouldnt be custom firmware for cup uch. Do you know where the vin is stored ? my old ecu/uch pack said d4f instead of f4r and vin number of pretty much 12345. Fitted 2nd hand setup and still says the same ? is it the...

Got to the bottom of this in the end Basically refitted later 172 ecu/uch and fired engine up from cold - idled normal and settled down to 800ish rpm idle when hot. I scanned it with clip and a load of old faults were stored relating to ct temp sensor etc assuming off the old car - cleared them...

Managed it with a couple of hours on clip playing about ? Basically recalibrate the multiplex network to set abs and steering angle sensor to missing Then recalibrate the clocks to remove course (Trajectory) control system to turn the esp light off. Job done no more network faults or serv...

You can take the heatsheilds off without any problems usually...you could fit some reflective heat shielding or similar if worried about it. Most motorsport places sell a variety of heat management products.

Coming along great? I need to reconfig the clocks on my kangoo to lose the esp on the 2nd hand ecu/uch i have. Looks pretty simple according to the manual, any tips ? Says batt off, reconfig without turning ign on etc. Do you need to manually input vin on clip ?

Knotted wheel on a grinder will remove factory underseal no bother. Beware its messy and time consuming, wear goggles as a trip to the eye infirmary is not nice (from previous experiences !) I would spot remove underseal where the rust is forming, clean up with knotted wheel, if metal is thin...

Check out the vin number on the current uch lol also case says n3 uch on the cover but scans as n2 ? Feck knows no wonder the rear door is always open. Thanks for reading ?

Update Jc5 129 with speedo sensor collected, get that fitted soon Took it to FCS last weekend, steady drive there and back drives great with new leads on, no hesitation or nowt. As still on knackered gearbox took it steady as 3/4th gear crunch is quite bad now. Late night greasy spoon on A453...

Make sure the header tank does not run low. If the coolant does not really come out give the header tank a blow.

Bleed it on cold engine when not running. I took it all the way out until good stream of coolant came out with no air bubbles.

Always meant to try some in my dci. Only been putting the odd tenner in the tank recently though not doing any mileage

Had a great day good to catch up with everybody? @Djw John we seen you and the RB on the hard shoulder of the M18 on way there was going to pull over but had no gear on us. Hope they get it recovered back to you asap keep on at them

Bodyshop will be able to repair that no problem. Theres a mega strong trade adhesive/epoxy for stuff like this possibly made by 3m from memory.

Coming together great ?

Had the pleasure of helping to remove a seized fiesta tdci injector today. Only had an hr and basic tools which did not really get it going. Inlet off tomorrow to get heavy duty on it ?

Walk away from that and find one with less rust

Sounds fine to me, some fecking useless mot testers out there. The clio is renowned for sloppy top mounts too when jacked up for mot and my springs are the same no issues. I had a massive bust up with an mot tester over my engine converted extra van. Engine is 1985 carburettor gtt turbo engine...

Try a new seal and sealant it might work for a bit, i think you will have to live with that oil leak unless you get the cam cover welded or replace the head though.

I would not worry if its oil on plug thread cam cover prob leaking a little bit. Replace coil pack if its got a black terminal it will have been arcing

Still nice to see the older cars about quite a few retros in daily use near me. My r5gtt feels tiny compared to any modern ish small car - corsa/fiesta etc. Its still a nice drive though feels raw no driver aids or nowt. I should make the effort to get it out more than a couple of times a year...

Id be stripping the bottom end to check pistons/rods and big ends with the valves kissing the pistons. Full freshen up if rebuilding.

Tickets booked for me and the mrs & Pm track slot booked. Best get the gearbox changed in the Kangoo soon ? looking forward to it

Double post

Wont airbag ecu need clearing/resetting due to the airbag firing ? I had one on clip and the airbag ecu could not be reprogrammed due to impact data stored and airbag light permanently on. Df 175 impact detected information was stored.

Normal for oil to be on the breather pipe..the pipe that goes to the left goes to the carbon canister. If the electrode on the plug is fouled with oil the compression is probably down on that cylinder poss worn rings or whatever - compression test it and go from there. At a guess issues with...

My Kangoo has a purple polybushed dogbone (powerflex ?) Rest of the mounts are new oem mounts and no extra vibrations seems quite decent and engine feels tight when on and off the throttle. However a couple of years ago i filled the stock dogbone mount on my 1.5dci with pu sealant and give it a...

Do the dephaser whilst doing the belts, you would be mad not to. Water pump can be done separately as it runs on the aux belt however its cheap so would do it in one hit. Also renew the aux kit if it has aircon and check the crank pulley as mine was shot.