Search results

Yes I see no mention of it going through 3 other connector blocks [emoji2357] Sent from my iPhone using Tapatalk

No wasn’t me . Just mistaken you prob for someone else on FB . Saw a post asking the exact same question. Must be common lol [emoji38]. Hope you fixed the issue. Sent from my iPhone using Tapatalk

Yeah , you got my reply I see on FB Sent from my iPhone using Tapatalk

If a vac line is pulled and it helps , then it’s running Rich . Poss a lambda issue . Try disconnecting the primary lambda sensor and run it in loop mode and see how you get on with that . Sent from my iPhone using Tapatalk

Like this @NorthloopCup , @LincsClio Mine got stuck in 3rd gear similar issue , bolt fell out. Sent from my iPhone using Tapatalk

Question : Seeing that people sell parts off clios ect , this meet would be an opportunity to allow buyers to collect said items for sale . Just saying , as I have an exhaust for sale and it would be costly to post ect . Just a little forward thinking if others had items for sale and were...

From memory, I think the 2 litre ball joints are bigger in diameter where it slots into the hub . Smaller engine clios deffo run a smaller joint . With regards to the bolts that secure it , I would imagine they are the same bolts used on all models . Sent from my iPhone using Tapatalk

It drains from the box in the drivers side scuttle panel area , and leaks down to the right scuttle drain / drivers wing / arch liner. Depending on angle will also drain out the centre drain tube from the scuttle Sent from my iPhone using Tapatalk

Ask on the Facebook pages , you’ll get a better response as not everyone is on this forum Sent from my iPhone using Tapatalk

Yes , two totally different wishbones . Cup has increased castor as opposed to non cup Sent from my iPhone using Tapatalk

I would imagine it’s straight forward , it’s only an integral item being swapped so I wouldn’t see any issue , only it being to quick as it’ll be assisted . Best to contact PMS/BRT and ask the question. Sent from my iPhone using Tapatalk

Yes , loving all the updates and all the footage . Some hairy moments !!! You’ll have to do a video on who’s who (names) and pit crew ect . Sent from my iPhone using Tapatalk

Subscribed Nathan Sent from my iPhone using Tapatalk

Would not think a bush is worn , you’d probably be able to hear and feel it if it was , it wouldn’t drive right and would prob produce a noise of some sort. Also this is not a common issue I have heard of , so hoping it an error with the gaiter or incorrect figment.

Check the multi plug behind the nsf kick panel trim , bonnet pull trim Sent from my iPhone using Tapatalk

Will that also effect the interior boot light [emoji362]? Sent from my iPhone using Tapatalk

I’m assuming your old shaft is being used ? Reason I ask is because if the shaft is slightly longer it’ll push the gaiter inwards to the diff and the rubber will want to naturally want to pop off as it’s under stress . Also , if the bearing wasn’t pressed on all the way down the shaft it will...

Put an additional fat cable tie around the rubber / bearing end and see if it happens again . Also was it a genuine part that was fitted ? Renault ones have a metal clip around them don’t they ? Sent from my iPhone using Tapatalk

I tagged a couple of mates on FB , hopefully will attend

One that I may attend , dust the cobwebs off the ole girl. Looks like a really nice venue @MrBlonde . Thank you for organising [emoji1303] Sent from my iPhone using Tapatalk

If it was that switch that was leaking then the PAS reservoir would be down on the level. Any pics of the area where the oil is leaking ?

I’d say your mixture is running a little to lean . Black = Too Rich White = Too Lean Brown = Just Right Sent from my iPhone using Tapatalk

Deffo AB ecu has to remain in the car Sent from my iPhone using Tapatalk

Yes the file is the picture below [emoji1303] Sent from my iPhone using Tapatalk

@adir Are you using a 197 throttle body ?? Sent from my iPhone using Tapatalk

Make sure all your pins are in the correct point @ ecu to each pin on pedal and motorised throttle. Don’t just continuity check , do a resistance check on each wire once confirmed it’s at the right pin @ecu. And also check that each correct wire hasn’t a short across to other wires and to...

Tell me what pins on the ECU your using for TPS and pedal ? Sent from my iPhone using Tapatalk

That type of bullet connector , normally air conditioning compressor . Is yours working ? Sent from my iPhone using Tapatalk

Don’t know the size but here’s the number 8200110994 Sent from my iPhone using Tapatalk

Do you have a M4R700 engine number ?? If so the part number could be 231000012R Have a scout about for one . Put that number in some search engines . Hope this helps . Sent from my iPhone using Tapatalk