Search results

if u can get a bit of heat on the hangers on the exhaust u can bend them slightly 2 suit an then pack the rubbers with more rubber 2 get the final fit. I found that if u just use rubber 2 pack the mounts an u have 2 stress them a lot 2 get it in the correct position the rubber mounts perish much...

if u can get a bit of heat on the hangers on the exhaust u can bend them slightly 2 suit an then pack the rubbers with more rubber 2 get the final fit. I found that if u just use rubber 2 pack the mounts an u have 2 stress them a lot 2 get it in the correct position the rubber mounts perish much...

get the scorpion 192 just ordered mine :)

yeh thanks guys gona try spot weldin a nut on 2mora..... An that freezin stuff works sometimes but i put that on b4 attemptin 2 undo them but suppose it cant work everytime lol gona try a small amount of heat as well an see how it goes!

Thats what im worried about i know there aint gona b much material 2 drill into, i wasnt planning on taking the engine out though to be honest im just giving it a fairly good detail, after all its a faired bike so most bits im cleanin will never be seen lol Although that might have 2 change if i...

Will that b beta then just using mole grips then? Havent seen anything that grips it on the outside before.

This is why i was thinkin i might just b beta drilling it out instead of using an easy out..... Lol an yeh thats the other thing i was worried about drilling too deep or not totally square.... Hmmm im prayin its gona come out after the overnight soaking! Begining 2 wish i had left it all on as i...

I have been stripping down my vfr400 over the weekend 4 a bit of tlc b4 summer. Was taking the exhaust off an one of the bolts sheared off an its stuck in the cylinder head. There is about 5mm still stickin out so im gona leave it in soak in wd40 overnight an gona give it a try with the moles 2...

are you talkin about the switch that isnt on the steering wheel? Cos if u are ive got a similar problem with mine. When i turn the cruise control (green light on dash appears) it stays on, but when i flick the switch the other way onto the speed limiter it pops back out again. If i hold the...

congrats on the purchase fella hope u enjoy it! I think i must spend about half my life in derby as i work there lol so will keep a look out 4 ya!

v power gets my vote all the way! Returns the best mpg i regulaly get 40mpg per tank, just goin 2 work about 14miles each way down the lanes

The thermostats and temp senders are a comon fault, i have replaced mine as it was stitting just under half way point and then moving around depending on how i drove it or if the car was in traffic. Now its perfect again and im getting better mpg as the engine is running at the correct temp all...

thats stupid m8 my polo was slammed 110mm, it was that low that it only just passed the brake test as the subframe was ground out on the floor when it dropped into the rollers! An the suspension might as well have been welded up it was that hard haha. Not 2 mention the inch of stretch on the...

Ive had the exact same problem! Sorted with a new thermostat, £15 Plus vat an it comes with a new seal if u buy from renault but also check fan!

If u have got some jump leads try connecting them up 2 another car thats running, if the car starts when connected to the jump leads i would say its the battery if not look down the starter/ connections route.

Alright m8 ive had same problem, i changed the sensor £21 from dealers, its an easy fit it goes on the thermostat housing an u can get to it without takin anythin else out its got 2 wires goin 2 it an think its a 22mm spanner you need but dont quote me on that lol if ur quick in with the new one...

Thought that might be the case, do you just have to remove the airbox to gain access? an are there any other gaskets/ seals etc i should be ordering at the same time or does it come as a kit? Also where is the best place to get one from? Straight from the stealers? an i suppose i might as well...

Hi i have had a problem with my clio 182 where by the water temp guage in the car was reading below where it would usually sit (halfway on the dial) even after driving for a long period of time therfore the limiter would kick in at 6,700, the only way to get it up to temp would be to drive it a...

not put 2 much grease on an there fairly tight in the carriers, dont use a pressure washer either, should there be a rubber backing on the back of the pads or thick layer of something as that had worn off in some areas so was wondering if its that?

hi one of my friends has got one of the new shape clio dynamics, there was a terrible noise at low speeds an under light braking. So i took off the pads on all four corners, cleaned them, re faced them an re fitted them applying plenty of copper grease. The noise under light breaking has...

I had 8j rims with 175s on the rear of my euro look polo, no problem with the mot as the tread didnt quite stick out the wheel arch when lookin from above although tire side wall an the rim clearly did! Although it can be a very grey area with the police i know quite a few ppl from the VAG scene...

I had 8j rims with 175s on the rear of my euro look polo, no problem with the mot as the tread didnt quite stick out the wheel arch when lookin from above although tire side wall an the rim clearly did! Although it can be a very grey area with the police i know quite a few ppl from the VAG scene...

Yeh worth it though! Not sure what im doin 4 the day while im down there!? or if i should stay over an have a night on the tiles somewhere down south b4 returnin home if i can get a few m8s involved lol

Thanks 4 the info guys mine is booked in 4 friday at K tec now not far from me only 348mile round trip! Lol worth it though at that price an knowing they have the genuine tools an that! Just hope it dont snap on the way down!

Do u know the name of the garage an there number? As mine has just hit 35k so im doin the belts as soon as possible. If this garage is well trusted an a reasonable price it might save me the job of doin it on the drive, and ive got 2 buy the locking gear so not sure how much money im gona save...

Ok i will try that first! it does seam to be comin from the passanger side though :( although its hard 2 determine these things sometimes.

When you say the hole, are you talking about where the thermometer sits in the left hand side wing mirror? And what was wrong with the heater vents, is there any easy way to diagnose the problem? Thanks for your help guys Andy

Can anything be done to stop this then? or do all clio's suffer with it?

When travelling above 73mph there is a whistling that starts coming from the front of the car, i was just wondering if any1 else had the same problem? as noises like this can be hard to find, not sure if its an air leak in the screan or something daft like the wipers???? Any ideas greatly...