What have you done to your car today ???

[linearvsunison]

I wouldn't put those T1R's back on come summer.

They're shite ?

surely thats a piss take?

Summer toyo proxes? I wouldnt put them on my kids little tykes car!

Not had any issues since fitting them in the Spring, but then again I'm driving a TCE not an RS so nowhere near as much power at the wheels and I don't try and drive it like it's an RS. If I disappear from the forum then you know what has happened - check the ditches around Coventry.

 

[donnylad]

I had them on the car when I purchased it, they literally tried to kill me every time it rained, it wasnt even when gunning it, sometimes just cruising along at 40mph round a bend of sorts and the cars sliding all over haha.

fitted PS3's and never looked back!

 

[STEVE.M]

Fitted stronger 400 front & 300lb rear springs to the Gaz GHA`s.

Removed the exhaust from the manifold back, had a blowing crack in the cat welded up, and refitted with new fitting kit, gaskets, clamps, nuts & bolts &

hangers.

Flew through the MOT with no advisories.

Full Geo booked for tomorrow.

 

[STEVE.M]

New seats

View attachment 1394155

Have you got a photo with the buckles?

 

[andrius7]

More than likely Strongflex, how do they feel on the road?

car has no Mot for now, will sort it next week, and let you know, but fittmentwas right

 

[Speedo Gonzales]

car has no Mot for now, will sort it next week, and let you know, but fittmentwas right

Cheers mate! I’ve bought the Yellow Strongflex ones

 

[Mr Trailer Man]

Have you got a photo with the buckles?

I can take a pic.

I've used Peugeot 206 rear belt buckles which are bolted down using the inside rear subframe bolt.

 

[STEVE.M]

I can take a pic.

I've used Peugeot 206 rear belt buckles which are bolted down using the inside rear subframe bolt.

Please do

 

[Mr Trailer Man]

Please do

You know the ones I mean though, these...

 

[Mr Trailer Man]

Please do

These should give you an idea Steve.

 

[JB21]

Tried and failed to replace side lights on the Octavia. c**t of a job!

 

[STEVE.M]

These should give you an idea Steve.

View attachment 1397597

View attachment 1397598

View attachment 1397599

Thanks for that.

I have a mounting point on the slider, so will use that.

I`ll do the passenger side 1st, now I`ve got the MOT done, and see where it sits height wise, as I suspect I will need side mounts or I will look like a 10 year old

that`s stolen a car.

 

[Mr Trailer Man]

Thanks for that.

I have a mounting point on the slider, so will use that.

I`ll do the passenger side 1st, now I`ve got the MOT done, and see where it sits height wise, as I suspect I will need side mounts or I will look like a 10 year old

that`s stolen a car.

Yeah if you're using sliders it'd be best to fix the buckles so that they move with the whole seat when it's moved forward and backward.

 

[STEVE.M]

Geo done at STS in Bedford.

Could even up the rear camber with a 20` shim, and the front caster is a bit out due to taking a stab in the dark where to drill a new hole when I had original

Ph2 wishbones welded & redrilled. to a supposed Cup spec.

The steering feels so right, perfectly weighted with the steering wheel horizontal in a straight line, I cannot be bothered to piss about with it.

 

[Amos91]

Geo done at STS in Bedford.

Could even up the rear camber with a 20` shim, and the front caster is a bit out due to taking a stab in the dark where to drill a new hole when I had original

Ph2 wishbones welded & redrilled. to a supposed Cup spec.

The steering feels so right, perfectly weighted with the steering wheel horizontal in a straight line, I cannot be bothered to piss about with it.View attachment 1397615View attachment 1397615

Of the few alignment places I have tried, STS seem to be the only place that get it driving straight first time.

Will be there in the new year once I refresh the suspension.

 

[Mr Trailer Man]

Geo done at STS in Bedford.

Could even up the rear camber with a 20` shim, and the front caster is a bit out due to taking a stab in the dark where to drill a new hole when I had original

Ph2 wishbones welded & redrilled. to a supposed Cup spec.

The steering feels so right, perfectly weighted with the steering wheel horizontal in a straight line, I cannot be bothered to piss about with it.View attachment 1397615View attachment 1397615

I take it you have camber shims on the rear already? Looks to be more than standard.

 

[Speedo Gonzales]

These should give you an idea Steve.

View attachment 1397597

View attachment 1397598

View attachment 1397599

What belt buckles are they @JamesBryan?

 

[Mr Trailer Man]

What belt buckles are they @JamesBryan?

The rear ones from a Peugeot 206, mate.

 

[STEVE.M]

I take it you have camber shims on the rear already? Looks to be more than standard.

10mm 1 degree spacers.

 

[Speedo Gonzales]

The rear ones from a Peugeot 206, mate.

Smashing, trip to the scrappies for me. I didn't trust the eBay ones

 

[Mr Trailer Man]

Smashing, trip to the scrappies for me. I didn't trust the eBay ones

Mine were off ebay ?

Off a breaker. Like £5 for 3.

 

[Mr Trailer Man]

10mm 1 degree spacers.

Thought about adding some more camber to mine, with it being used on track especially.

 

[Speedo Gonzales]

Mine were off ebay ?

Off a breaker. Like £5 for 3.

Gonna give some Facebook car breaking scragheads a message now?

 

[Karlos182]

Replaced the windscreen washer pump after the old one made a lot of noise but pumped nothing. Followed the guide on here after finding a replacement on eBay for £5 ??

 

[donnylad]

where is the guide mate? I want to do the opposite and remove the pumps and bottle etc any weight saving is good weight saving

 

[Karlos182]

Here’s the link:
https://www.cliosport.net/threads/windscreen-and-headlight-washer-jets-fix-guide.496162/
If you’re not a paid member, you won’t be able to view it though.


Sent from my iPhone using Tapatalk

 

[donnylad]

Here’s the link:
https://www.cliosport.net/threads/windscreen-and-headlight-washer-jets-fix-guide.496162/
If you’re not a paid member, you won’t be able to view it though.


Sent from my iPhone using Tapatalk

thanks karl! fully paid here ofc!

 

[cat171]

Sunday - fitted new 'plain plates' on, I did buy a set a couple of years ago but never put them on, when I took the plastic off recently they'd gone slightly weird, so I got a new set.
They were cheaper than the crappy looking ones the dickwad in the shop wanted to sell me last week. Happy days!

 

[masekwm]

Put pots of cat litter in, as it's now in the garage until end of Winter

 

[imprezaworks]

Your cat's s**t in your car?

 

[Andy Tims]

Moved it off the drive to make space for the in-laws to park.

Happy Xmas

 

[Landyman]

Moved mine on to the drive so there’s no space for the in-laws to park

 

[DrR]

Drove it to work.

 

[Tonyclio]

Well spent the last couple of days excl Xmas day removing gearbox + subframe. First time so proved 'interesting'. Subframe bolts to 3 hours to get out due to being seized.

I take my hat off to you guys who do this outside in poor weather?

Subframe off to be powder coated and gearbox off to NorthloopCup for Gripper diff to be fitted....... roll on on Harewood Hillclimb 2019 season!

Now just need to source a nw clutch (while it's out) and drivers side drive shaft due to split gaiter...grr

 

[Louis]

Washed it then it got dark

 

[Karlos182]

Changed the manifold to cat gasket and bolts, after the old ones broke free. A simple job in theory, but spent most of the time trying to saw off the old bolts, which had rusted on.


Sent from my iPhone using Tapatalk

 

[xcore]

Changed my 172 cat today, what an absolute ball ache, defiantly a 2 man job with one holding the bolts from the engine bay!

 

[LostInSpace]

Bought it and drove it home ?

 

[STEVE.M]

Changed my 172 cat today, what an absolute ball ache, defiantly a 2 man job with one holding the bolts from the engine bay!

You little pussy , be as defiant as you like, but you enjoyed the enjoyed the 2nd man working on the nuts.

 

[JB21]

Changed the back box for an upcoming MOT on the Mondeo ST which was a piece of piss.

Dropped of the kerb ramps and ping, snapped front spring. Tried changing that and sheared the pinch bolt in the strut/hub carrier. Used hub now required.

Both tie rods also needed replacing.

On closer inspection both bottom ball joints had very slight tears and as they are rivited in the whole lower arm needed to come out. Gets better as you need to lower the subframe to get the ball joint out the hubs and rear bush bolt out.

Fuckin nightmare!