Search results

Hi. I went to my car earlier to check and see if the aircon had any pressure in it as i want to change the condenser. When I turned it on I get no blowers at all in the car. Wether I select hot or cold, aircon on or off etc nothing. Pretty sure the heater abs blower worked a few months ago but...

Hi. Maybe a stupid question but here goes. I’ve got a set of Turinis for my 182 and would like to get some new wheel bolts as the ones I currently have are naff. What is the correct size abs style please and any recommendations? Wheels are OE Renault and cup offset. thanks in advance

cheers, assume i just add it into the condenser/pipe and the fasten it up. or is it easier to add it through the charging port by taking the valve out.

Thanks Louis. Just got the nissens one MLB said but from autodoc for £63.90 which isnt bad i thought. I had a look for threads and guides but will search for one of yours. Thanks all. Hopefully have it back on the road soon (been on my drive 15 months now) and will be looking for somewhere in...

Thanks. condenser is out of stock on the ebay one but found same one on autodoc for not much more. Do you know if there is a guide for replacing them anywhere or is it simply slam panel off, drain rad, disconnect rad and condenser and lift out the rad, condenser and fan in one go?

Hi, I'm slowly working on my 182 as I get chance and the aircon condenser has definitely seen better days and isn't secure. It flaps about at the bottom as looks like the bracket is totally shot. I'd like to replace it myself (maybe the radiator aswell but will look at that when its out) and...

My brother in law is slowly doing this conversion on his.

I’ve got a mains Bosch green one. It has taken so much hammering over the last ten year and still going strong. The pukka Bosch blades are expensive but I buy cheap ones from eBay, Screwfix, toolstation etc and they fit fine and work well. I thought about cordless but there has only been maybe...

Hi, As with a lot of people I've got board lately and decided to have a play with my 3d Printer. Decided to try a DIY air duct to go in the spot light hole. Here's the results of 1 1/2 days play. What's your thoughts if any? Also I don't have ducting and not planning on doing it. just fancied...

Yes please if you could. do you want to pm me some paypal details and a price posted please buddy

Hi. Does anyone know the part number for this Milltek cat to exhaust adaptor pipe? Thanks in advance

my old one jammed like that. got the wife to pull the handle while I joggled the bonnet towards the drivers side. catch was pulled enough for me to open bonnet

Probably not the answer or daft thought but any chance the wires are in the correct place but have snapped off the fuse base. then maybe bodged back over the top and pinned with the fuse.

Hi, Can anyone tell me the part numbers for these headlight connectors please or a link to where I can get them from please? Thanks in advance

Hi, I'm just wondering if anyone has bought parts from Partsouq before. Been looking for a wheel arch liner for a while now and going to just buy a new one but spotted their website. They seem rather cheap and not sure how a company in UAE is nearly half the price of anyone else. Postage to the...

I’ve got a few ryobi drills inc the 400nm impact gun. Works ok in the smaller batteries but kills them quick. I bought a cheap 6.0Ahr one off eBay and it’s been great. Was £26 for the battery. Think they’re £32 now.

I use an LED fish tank light above my bench.

Contact @fil_b on here. They've just listed 7 for sale starting at £15 each

Nah. Hull.

Thanks for all the replies. I’ll have a think. My wheel nuts are kinda crudded up so will look pants with the wheels I’ve just got so want to replace them all. Some places not too far from me you’d be tempted to put a d-lock on your cat just in case.

Hi. Just wondering what locking wheel nuts people recommend. Car doesn’t have any spacers fitted and will have either std 182cup wheels or Turinis on. Thanks in advance.

Wow. Safety first lol.

i wish lol

Thanks for the replies all. Much appreciated. Have ordered some pads for my stands. Thanks again.

Hi, i use the frame rails at the front when i put my car on stands but where do i put them at the rear? I need to drop the rear axle so that i can change the springs but don't want to use the sills as they're not great. Thanks in advance

Will do. Will see if I can find some rubber inserts on line first but if not I’ll have a play 3D printing one in rubber.

Cheers. Is it just sticky tape? Might see is I can print some blanks. Need to replace the under seal that’s worn away aswell.

Hi. Can anyone tell me if there is supposed to be a blank in the middle hole. Seems odd that there is one either side. Both sides of mine are the same. Also on the frame rail. If yes where do I get them from. Thanks in advance.

Thanks all. What’s the full name of the one in Doncaster please? If I search dds Doncaster it comes up with a dentists.