Search results

Just had a good match on Highrise 15-4 and Quarry 14-5 I was chuffed to bits 2nd overall :D Took a while to find a decent match where people actually played the game but was good Plenty of drops (for me anyway lol) and a good amount of UAVs Came accross some boosters on a few matches so just...

That ounds like the low pressure one from the header, Sure i had a 17mm spanner in my hand earlier :S

I just use Panel wipe, Why spend a fiver on a small bottle of tar remover when you can get 5 lires of panel wipe for the same price lol

Cant you get some belts out of an old meganepug or something like where they bolt to the floor, FFS I would not be driving that :o Invalid insurance FTL

Lambda socket? I gave up on it, I was lying there in the Rain thinking WTF am i doing :S threw the towel in and Rang the local specialist, Quoted me 4 hours (£160+VAT) for them to remove the pipe, Ring me i run to Pirtek and get a replacement then they refit it and flush the system through with...

Mine did it almost a year ago, Turned it on and off and its still fine :$ touch wood

Sliders free? They will need to bed in too

How the hell are you meant to do it? I've just took a gander because mines gone and got wet through and bloody cold in the process, I got as far as removing the inlet and a heatshield bolt lol I'm assuming you get at it from the top? What do i need to remove to get at it and remove it? Thanks

Just had this happen today :( I have noticed and so had my Dad lol the block paving has been getting stained, I didnt think anything of if as i'd only changed the filter a few days prior and assumed it was off the block. Got Vibratechnic mounts on it at the weekend, Initially i thought this was...

lol good lad :approve:

Back right down and about 60mm on the front with no scrubbing thats on standard wheels, Aftermarket (ET37 7" 16s") on mine same but expect it to scrub on a quick drive on bumpy roads :o

I did Lol lots :cool:

I've distorted my Purple PF bush on my 182 :o I've been thinking about a Rose joint linkage in there B)

Whats the lifetime on the Rs2s like? I've still got to replace two of my PE2s after 2 years :o The other two are holding out well too and theyre easy a year and half old, Got about 20k on one pair :)

Looks good mate, Just right for your mate to hang on the back with his Rollerskates on ;)

Local one near me managed to put a dint in my bonnet near the centre line, Only somehow they managed to dint it pretty much halfway up the bonnet, So if you inmagine from the front of the car theres a foot of dents not small either :( Spotted it a few days after sadly and didnt bother again...

Errm Group N bushes arent bad! When everythings cold yeah it vibrates a bit but after a few minutes its fine :S

and the rest, been on The OC a looong time and still havent seen one at £700 :P

Thats the first thing i noticed when i saw you pictures, The twisted one has an offset bush on one end to keep the dogbone inline, which i'm wondering how to overcome, All i can think of at the min is an Ali spacer so it'd work, but then i dont want to stress anything But been rose jointed i...

Any reason behind that?

Obviously it could be done, I've got a powerflex one on mine at the minute along vibratechnics engine mounts, It feels noice :D I could see when i took a look at my dogbone mount, because my oldengine mounts were weellll shagged. Its took a lot of abuse and the bush was looking slightly...

Cheers mate, Literally just found it on a .pdf doc Chamfered edge goes towards the car as you say

Ok Searched, Gone through 8 pages, Found a few nice project threads now nackered lol I'l be doing my brakes tomorrow one thing thats got me a bit iffy is the spacer that sits up to the bearing to stop the ABS rings fouling??? I've not had a disk off yet so dont know what it looks like but the...

Brembo HCs ~ £55 at NW Performance Standard Rears and pads ~ £120 NW Performance Mintex 1144 ~£50 sheets at Kam racing Should see you right for a few spirited road drives! :approve: Dont bother with the braided lines unless you feel you really need them or standard lines are looking perished!

I'd say check the ABS ring!, I guarantee it has a slight crack :o

IMO depends how its done ie not a rattle can job lol, Got a set of 182 cup wheels 4 years old that were painted still pretty mint bar the 2 or 3 stonechips on the rears :cool:

Nope, Are you heavy on the brakes? My brakes were like that when i bought mine i'm guessing a steady driver before me, I stripped everything and regreased it all fitted new brakes, 2 years on they're still doing a clean sweep, They've come to the end of their life now, Well the disks have still...

Up to you, I toyed with the idea but the damping rates will be different between shocks for the different Chassis and engine combos! If i was to do it i'd do as you've said, and weld the washer to the strut, but if your innacurate lengthening the hole you'l have issues later when you get it aligned

God a good 20k on on mine now :approve: Still got 6-7k left in them too lol, Moneys worth ;)

cue pm, I want head, you have nice lips yadda yadda ;) £200 sheets is pricey though, Are they removing the roll bar too, I'd be thinking they would at that price!!!!