Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!
I was a bit unsure of whether to fit Piper Cams as even though they have been produced more power than 428's (see below), they have been known to be a little noisey - but as they are now supplied with a shim to keep the follower in range and keep them quiet I went for it...
I was recently looking at my PH2 172 and noticed the plugs were there for CC/speed limiter.
After a quick read from this thread i thought i would give it a go.
Once all the parts arrived and were plugged in everything worked! :)
An ESP button came with the panel and there was a plug in the...
Do lower spec. models have the same BRAKE CALIPER positioning as a 172?
I need to get some brackets made up for a set of Wilwood calipers for my 172. I was going to give a hub/disc/caliper to a machinist to get these made. A 1.2 hub is far cheaper and easier to source!
I've been thinking about getting my Iceberg silver Clio roof vinyl wrapped. It would either be in gloss black or carbon fibre. It is now on anthracite turinis..
Can somebody have a go at black?
Cheers
I am going to get my skirts painted because they're pretty stone chipped.
Before i remove them, i wanted to double check you can get the factory rivets that hold them on?
Has anyone got a part numer?
Hello
I wen't out for a drive last night and it has started whining.
If you rev the engine out of gear or with the clutch in it's fine. When driving in gear there is a whining noise, the higher the revs the louder it is.
It started doing it now and then but now it does it all the time...
Hello,
I've got a valver with a few problems:
The ffront fog lights don't work at all, the bulbs are fine. The light on the dash comes on when they are turned on but thats about it.
My heaters only blow cold air, no hot air?
The front window wipers go crazy, the seem to do what they want...
Hello,
This is my second attempt at this as my pc died the first time...
Today i thought i would lower and fit my new discs/pads to my valver, simple i thought. After lowering the rear end i let the jack down, but as i pulled the jack out i caught a fuel line and ended up with fuel everywhere...
I have just got some -50mm lowering springs/adjustable absorbers for my valver. I am running Williams alloys with 195/45's, i just wondered if it is going to rub?
I have just bought a set of these but two of the center caps are missing. Does anyone know if a set of original Williams ones will fit, can i get these from Renault?
If not any ideas on how i could get hold of a set?;)
It took me about a minute to find the new 'New Thread' button...
I am having a few problems with me rear wheel/s? locking when i brake hard on my MK1 Clio. I am pretty sure its only the one side locking when harsh braking, especially in the wet. I have put a rear axle from an RSI so i could...
Few bits for sale:
Clio <98 Red dot brake pads dimpled DNX discs Mark 1
http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&rd=1&item=230186115762&ssPageName=STRK:MESE:IT&ih=013
Inazuma Shift Light - plug and play...
Hello,
Finally it was sunny, so i had a quick clean and took a few pictures.
Some of the mods:
285mm discs, Williams calipers, Goodridge braided lines, K-tec camber bolts, pagid pads, Proxes t1-r's spax springs and adjustable absorbers front and rear.
Cold air intake with K&N replacement...
Hi,
I've got hold of a central locking switch, a relay, door locks and the wiring loom for my clio. I have plugged the relay in the only slot that had contacts (top right) and it does nothing, any ideas?
Thanks on advance
i recently got a new front brake setup for my MK1 Clio:
EBC greenstuff pads
K-tec big disc kit
Willy calipers
Goodridge braided hosesAfter driving a mates standard '04 Clio my brakes don't seem to have the same bite. Mine are definately an improvement from what they use to be but i have to...
My mark 1 clio 1.2 0-60, just a few performance mods. Before you tell me to get a proper car, i'm 17 working part time...
http://www.youtube.com/watch?v=xqxlk-zf3-U
An old'ish picture:
Hello all,
I have a MK1 Clio which is lowered 35mm on the front, 40mm on the rear with spax adjustable absorbers. I have just ordered some camber bolts for the front, will these make much difference? What settings should i use? I have been told to go for 1 degree negative with my tracking...
Hello all,
I was thinking, is there any difference between a normal and a williams rear anti roll bar? Will a Williams one fit a normal MK1 as i think the axles are wider on the Williams?
Hello,
I have just got a set of 16v bumpers for my MK1 phase 2 clio. My current bumpers are black plastic and have no fog lights. I bought a front fog light switch from ebay and have just fitted it. After removing the blanking switch to fit my fog light switch, i noticed there was a plug, i...
The biting point on my '95 MK1 phase 2 is right at the top, does this mean my clutch is fooked? Are they reasonably easy to fit, what do i have to do, will a Haynes manual explain?
Cheers