Maplin airbag resistor help please

[CBetts]

Hi

Could anyone be so kind to point me in the right direction for the correct airbag resistor. Gonna fit my Sabelt wheel tomorrow and need to pop to maplin, been looking on the website but im unsure which one I actually need to switch the "serv" light out, is it likely to be this one? - http://www.maplin.co.uk/3.3k-ohm-to-9.1k-ohmmetal-film-0.6w-resistors-341616

Thanks guys

 

[Gaz_]

Yup, anything from 2-6 ohm will do. The light clears when the fault does, so no need to go to Reanult if it didnt work first time

They sit in the boss. The airbag wires are connected to the airbag ring. This spins with the boss, so nothing crosses over.

Like this

Resistors go in the x2 airbag connectors (ignore the fused resistor in hand lol)

Horn connector is pushed down into the boss there. I'd simply get some spade connectors, connect to your horn, then connect to the horn connector (cut off and keep in safe place if need be)

 

[jenic]

The one you link to is 3.3k ohm, thats 3300 ohms.

You want around 3.9 ohms. Just go to the geek counter at the back and ask for some 3.9 ohm resistors, get them to test them too to make sure they are the correct resistance because they always get them mixed up, they'll have a multimetre behind the counter anyway.

Here you go:

http://www.maplin.co.uk/1-ohm-to-8.2-ohmmetal-film-0.6w-resistors-341668

Select 3.9 ohm from the list, 24p each, bargain!

 

[domjolly]

Are these the same resistors for under the seat?

 

[Naith]

process is the same for the ph1 too yeh?

 

[jenic]

Are these the same resistors for under the seat?

Yep.

Not as clear as to where they go under the seat but The Boosh! has done a great guide in the guide's section.

 

[CBetts]

Cheers guys

 

[Gaz_]

process is the same for the ph1 too yeh?

not too sure I *think* they might only require one resistor....?

 

[akaboogie]

yeah 3.9omh in each air bag connecters and make sure you tape them up then job done...

did mine yesterday.....

 

[Weo]

Sorry to bring an old post up, but you guys seem to know what your on about.

Changing the seats in my 197 to recaros, and the resistor packs are £30 each side. Seems a bit steep for something that is usually so cheap, was wondering if anyone's knows what resistors and how many I would need for the removal of my 2 front seats. To replace with not airbag recaro seats. Thanks.

Will

 

[jenic]

As per this post, the 3.9 ohm ones from maplins work, you'll need 4 to do a pair of seats.

There are a couple of guides in the guides section, I used the one by The Boosh!

The one you link to is 3.3k ohm, thats 3300 ohms.

You want around 3.9 ohms. Just go to the geek counter at the back and ask for some 3.9 ohm resistors, get them to test them too to make sure they are the correct resistance because they always get them mixed up, they'll have a multimetre behind the counter anyway.

Here you go:

http://www.maplin.co.uk/1-ohm-to-8.2-ohmmetal-film-0.6w-resistors-341668

Select 3.9 ohm from the list, 24p each, bargain!

 

[Weo]

Thank you, do I need to solder this in or is it crimped? Or just tape in? Sorry for 101 questions

 

[jenic]

I just doubled over the legs so they push in tight then taped them over. You could cut and solder for a better connection but I never had a problem.

The wheel ones are a bit more fiddly

 

[Weo]

Cheers jenic!

 

[1812lsd]

Maplin code: M3R3

 

[James28]

Use my guide in the guides section! Its the top one :approve:
Explains seats and steering wheel!

http://www.cliosport.net/forum/show...-Airbag-Light-removal-Aftermarket-Seats-Wheel

 

[Weo]

Maplin code: M3R3

I got M3R9 which was for 3.9 ohms resistance as jenic said

 

[jenic]

Both will work mate, 3.3 ohm or 3.9 ohm

 

[Skeeter]

So do you need 3.3kohm or 3.3ohm?

I've got two 3.3kohm ones from a mate and they don't seem to have worked. It's a bit of a pain getting them to sit properly so they make contact, but I've been trying for a while and got nowhere.

 

[1812lsd]

3.3ohm

 

[Skeeter]

Doh!

 

[Rich_172]

Done steering wheel this morning and uses 3.3ohm resistors. Airbag light has gone off but still got SERV, traction control and ABS lights on. Any ideas?

 

[benkay]

Cracked ABS ring?

...or crud in it?

 

[Rich_172]

ABS ring was changed 2 weeks ago

 

[benkay]

Definitely properly? Could it be that whoever fitted it did it wrong or put a ring on there with incorrect number of teeth?

 

[proostjoost]

You guys seem to on top of the subject here.
I studied the electrical diagram and got a pinout of the ecu.

On the airbag ECU the following pins can be found:

- 2x twin airbags front
- 2x belt tensioner front
- 2x lateral airbags
- 2x switch/sensor for lateral airbags
- 1x driversseatposition switch
- 1x switch for inhibit airbag passenger
- 2x belt tensioner rear (so far as I now never equipped on Clio's)

- CAN H
- CAN L
- Mass
- K2000 contact

 

[proostjoost]

Sorry forgot to introduce myself:
My name is Joost from the Netherlands, owner of a Sacre Bleu ! Pilote damage desastreuze ! Clio
Also active on the dutch site where you find a electrical diagram:

http://www.clioclub.nl/viewtopic.php?f=6&t=19091

 

[proostjoost]

Does anyone now the normal electrical state of the switch/sensor for the lateral airbag please ?

 

[LeeRS]

Going to fit ky wheel soon. Once I remove old one and airbag etc will I get a serv light or airbag light?
I will be fitting the resistors as above but will it need the code clearing before the light goes out?
Just getting ahead as I will need to borrow my mates reader if so.

 

[mossyv6]

Hi Lee,

As long as you fit the resistors into the airbag orange and green airbag plugs all your lights will stay off.

Be careful with the steering wheel angle sensor - makes sure it's all lines up and the bubble indicator remains yellow. Otherwise this will illuminate the traction and service lights.

 

[mossyv6]

Oh and for safety - disconnect the car battery for 15 minutes prior to messing with the airbag

 

[LeeRS]

Nice one. Is there 2 resistors required then I take it?

Deflectors arrived today btw. Nice one.

 

[mossyv6]

Yes mate 2 resistors about 15p each from Maplins.

And good news about the deflectors

 

[LeeRS]

Quick can I use 3.9s? Got no 3.3 in maplins now

 

[mossyv6]

I put 3.9 and ok.

 

[LeeRS]

Sound.
79p well spent.

 

[LeeRS]

Is there a guide on here for fitting aftermarket wheels with pictures? Will be able to do it myself if I can see before hand what needs to be done. Search bar doesn't work on my smashed phone screen unfortunately lol..

 

[MrBlonde]

@LeeRS did that resistor work?.as my lights come on now and then.

 

[LeeRS]

Yes mate. 3.3ohm resistor x 2.
One on each if the airbag connectors.
75p ish each from maplins.

 

[LeeRS]

3.9 also works mate. Just realised what you were asking.