Search results

Sounds like a little bargain, nice little project, nice one ?

I like that idea, any good ? You had one ?

Thanks for the efforts but none of them are listed anymore

Bought what I thought was a LED bulb for rear number plate light today from halfrauds after searching on there system computer it came up with the ones below. Clearly not correct, what do I need? . And what are the ones I have for they don't look like ones I've seen anywhere else on the car, cheers

Yeah bit of a fiddle because your on the floor trying too do it but not too bad, yeah both on eBay

Just grabbed some photos for you

Sorry I totally forgot I posted saying I'd take photos put them up in bit mate

Most people would go for Fabia splitter, there marked in the centre so start there screwing it in with some 1" self tappers then you trim the ends as they are a bit longer, door trims are easy , on the inside of the door there's a round plastic grommet pop it out and with a screwdriver push to...

What's the location on this, interested in rear bumper

For what it costs you may aswell, my water pump failed the other day causing my timing belt too come loose whilst it was getting sorted I did the lot although belt didn't look that bad, aux belt aswell

Sounds like a misfire to me , spark plugs and coil pack possible

Chance would be a fine thing

I'm confident in doing it just want it recessed which looking at the picture it looks like it is slightly adjustable And no I wouldn't want too be tripping over it would be an inch or so sticking out max

It not awful whereas I can't stand cherry bombs. No its never going too sound like a 1*2 with a Ktec setup with a decat that is not my aim, these have a nice little rasp to them, is there any other recommendations only looking too change backbox

Not quite but I think it sounds ok. Bit of a gay one but all I can find , and I'm sure it will sound better on a 1.6 with an induction kit

The silly responses are due to the fact people don't respect other people's opinions / choices

Doesn't seem like the best place too get a response looks like a quiet forun, but thanks for help

Until that day comes I just want an answer to my questions please if you can help

Just some quick questions on the hornet exhaust as I'm looking too make some noise and these look quite easy too install wondering if anyone Has any experience with them. As I say just looking too be a bit noisier as I have fitted an induction kit but only get a noise when accelerating. Can you...

The bumper and new style boot was the Phase 4 Variant of the mk2 2006 '56'-'58' reg although the mk3 came about 2005 '55' reg

Non sport bay, few more bits too do , going too spray manifold that shows through the cover yellow and battery casing yellow

*little update* After some advice given I fabricated a heat shield from some scrap metal for the induction kit, whilst I was at it I sprayed some other bits up and used some iron out too clean up underside of bonnet now looks like New, just want too spray battery casing yellow and I'm done

I fitted apex on a non sport and needed sport dampers Now they work a dream , and yes mot fail

Around the £100 Mark give or take

Conkered this today Stripped out factory airbox Installed breather for crank pressure thanks to @MonkeyKnifeFight for this solution Then put the jigsaw together Happy with noise and look results, no noticeable power difference but this Is just a project too clean up the engine bay...

Decided not too buy a kit and do it with silicone pipes now, and I can get a t piece too solve the other inlet issue . And I can do it all in blue piping which I would prefer

Decided not too buy a kit and do it with silicone pipes now, and I can get a t piece too solve the other inlet issue . And I can do it all in blue piping which I would prefer

Which did you go for, think it would look silly with a small cone filter and and surely a catch can would be ratlling around all the time which would be equally annoying

Going too bump an update, took some stuff apart today and as well as having the main air inlet which Is 85mm there is another small air intake which I'm guessing too cool the oil as there was residue around it, how do I get around this if I bought a silicone hose too go straight onto the block

I looked into buying a bit of hose for the oval bit but it's 115mm so was quite expensive, see how cheap a kit I can get