Just be mindful of the post cat sensor. Mine was fine, then this weekend I fitted a new exhaust which has made the cat sit higher, that and pulling the engine forward has pushed the post cat sensor into the heatshield and gear linkage which then blows the fuel pump fuse when it shorts. Now I need a new sensor!
ClioSport.net
Register a free account today to become a member!
Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!
-
When you purchase through links on our site, we may earn an affiliate commission. Read more here.
MrBlonde
ClioSport Club Member
This worked for me also on my cup,losen engine mount and pull engine towards you and then tighten.I think its exhaust that knocks on the bulkhead.
cjgower
ClioSport Club Member
Thanks all. Have tried and tested yet, but, I did manage to move the engine forward a fair bit yesterday.
Also had a chance to photograph top mount setup. Does all look correct?
These are the top hats. The nut appears to spin on one of them but is fixed on the other. No idea if that’s correct.
I’m sure that it’s separate to the knock and hopefully the engine position is the culprit. Will try tomorrow when the weathers improved.
Also had a chance to photograph top mount setup. Does all look correct?
These are the top hats. The nut appears to spin on one of them but is fixed on the other. No idea if that’s correct.
I’m sure that it’s separate to the knock and hopefully the engine position is the culprit. Will try tomorrow when the weathers improved.
Mr Underhill
ClioSport Club Member
Looks all good to me. Obviously, I can't see all of it, but I assume this is how it's assembled.
cjgower
ClioSport Club Member
Yes from memory, this is exactly the setup/order. I didn’t realise there were two types of top mount until researching this past week.
Every 172 I’ve owned has already had the updated design without the spacer but. Cheers
cjgower
ClioSport Club Member
So, i've taken both shock absorbers out, and unassembled both. The passenger side spring looks like it had been compressed to the point that the bump stop had split in two. Should the spring be compressing to the point that the coils rub together? (pic below)
Measures taken so far to try and cure this issue:
- New top mount bearings
- New upper gearbox mount
- Polybushed dogbone
- Swapped to OEM dogbone
- Swapped back to Polybushed dogbone
- Triple-checked steering rack bolts are tight
- Moved engine forward and tightened down the engine mount
Knock is still there. I will be booking the car in to be looked at by a garage... although I am wondering if larger outter arb bushes would help? mine look almost loose. I ordered 23mm outter bushes for reference and the arb on the car when dismantling looked to be new/recently swapped.
Measures taken so far to try and cure this issue:
- New top mount bearings
- New upper gearbox mount
- Polybushed dogbone
- Swapped to OEM dogbone
- Swapped back to Polybushed dogbone
- Triple-checked steering rack bolts are tight
- Moved engine forward and tightened down the engine mount
Knock is still there. I will be booking the car in to be looked at by a garage... although I am wondering if larger outter arb bushes would help? mine look almost loose. I ordered 23mm outter bushes for reference and the arb on the car when dismantling looked to be new/recently swapped.
cjgower
ClioSport Club Member
Turns out I was looking in the wrong place. Got my brother to take it to work. The ball joints where the incorrect type, and where moving separately from the arms. Not great!
It’s ok now, however, I’ll likely get some second hand Cup arms as spares just incase any wear occurs again.
In the meantime, I finally got some ramp pictures. Nice to see it from afar, rather than on the floor 🤣
Still a few bits like heat shields and trim to put back yet. When I can be bothered
It’s ok now, however, I’ll likely get some second hand Cup arms as spares just incase any wear occurs again.
In the meantime, I finally got some ramp pictures. Nice to see it from afar, rather than on the floor 🤣
Still a few bits like heat shields and trim to put back yet. When I can be bothered
cjgower
ClioSport Club Member
Not much to update, but I've booked Snetterton for the 13th of August which is exciting. Took the car the scenic route to Birling Gap yesterday - the car was faultless.
No real plans to change it up with mods, other than getting the alignment dialed in properly with AW Motorworks in late July.
Cosmetically speaking, the car needs some love. I don't know if it's immediately visible here, but the door is not the same shade of Mondial blue as the rest of the car. The headlights are faded so will be replaced. The drivers side side skirt is also battered, so I need a new one of those too.
Jobs still to do:
No real plans to change it up with mods, other than getting the alignment dialed in properly with AW Motorworks in late July.
Cosmetically speaking, the car needs some love. I don't know if it's immediately visible here, but the door is not the same shade of Mondial blue as the rest of the car. The headlights are faded so will be replaced. The drivers side side skirt is also battered, so I need a new one of those too.
Jobs still to do:
- Replace headlights
- Replace drivers sideskirt
- Replace Aux belt
- Oil change before Snetterton
- Camber shims on the rear, camber bolts on the front
- Fit 172-cup door pillar badges
- Buy a new stainless exhaust
Advikaz
ClioSport Club Member
Epic.
I’ve done the same (spent more than the cars worth and then some) 😂
Poverty friends
cjgower
ClioSport Club Member
Something I’ve had planned for a while; finally getting married after 15 years.
Naturally, after 5 Cups during that time, it seemed fitting that this one was the wedding car 😂
Got Snetterton booked for August and alignment booked in for 27th of this month.
As it was the big day, I tried to get the car looking as good as possible. So fitted some new headlights. Definitely helps make it look a little more cared for.
Long term I’ll retire the car from track duties and use it as a well cared for example on the weekends - respraying bumpers etc. Hopefully a track oriented 250/R26 will be on the cards.
Naturally, after 5 Cups during that time, it seemed fitting that this one was the wedding car 😂
Got Snetterton booked for August and alignment booked in for 27th of this month.
As it was the big day, I tried to get the car looking as good as possible. So fitted some new headlights. Definitely helps make it look a little more cared for.
Long term I’ll retire the car from track duties and use it as a well cared for example on the weekends - respraying bumpers etc. Hopefully a track oriented 250/R26 will be on the cards.
cjgower
ClioSport Club Member
Congrats Chris! getting married to the Cup...I mean wife
Was mentioned in the speech. "I'd like to thank my new father-in-law for letting me marry the love of my life..... for those that haven't seen her, she's parked outside with blue ribbons on."
Got people laughing 😂
