Search results

you should only have 2 lambda holes in your decat, not you exhaust after the cat, my car is the same as yours.

could i not run the whole megane set up i.e engine and Ecu aswell?

hi all To hybrid my valver i know i need an F7R bottom end or a complete williams or F7R magane engine. Can i use another renault 2ltr bottom end from a laguna 2.0 8v? or is this completely different, Im thinking it is but just checking the obvious. Would ask on williamsclio, but i cant seem...

just slowly but agressivly pull the door up when fully open, the hinges are very strong as they are welded on so will need a good pull to bend back into alignment, wont need much tho, maybe also readjust the catch on the b pillar too.

next time it goes off check the red light down near the gearstick, if it flashes 3 times after the alarm has gone off (dont put the ignition on as it cancels it), then the alarm was triggered by the motion sensors, they are very sensitive from the factory, do a search, you can switch the wires...

my valvers a 91 (J) will i need a cat for the MOT?

didnt need to jack the car up to fit the exhaust....

had a friends set of 18's kicking about so whilst fitting my decat and realigning my exhaust i put them on.... for 5 minuites.

all buttons were reconnected, i basicly removed the buttons and cliped the loom back in. just left with these. car has lecy mirrors, manual sunroof tho.

bump

Hi Stripped my valver out and had to unplug a few connectors to remove the dash but i was left with these lose conectors when i put everything back together. there is no obvious connectors to plug into!? this one on the drivers side: This one below the guages: And these two...

first car was this, miss this car so much, it was s**t but we went through so much. Now have this, quality car, just a bit expensive to run and repaire: and this:

i have a 172 and went to test drive a 197, basicly told me to f**k off, went to honda, test drove a bread van and they even offered me a cup of tea.

get an original rubber ph1 strap, thats roofing strap!? lol

the 'hybrid' back in the day ;) -55mm all round.

mine too

you will need to rinse the foam thoroughly, i spilt a pint of milk in my passanger footwell, still smells 3 months on, get some zoflora on it.

Nasty. I think your going to have to bite the bullet and strip the car to properly dry it out, its the best if not the only way.

well mine has 2 and i oredered a ph1 decat only to find its an inch to short and only has 1 lambda sensor, sent it back to have it exchanged for a ph2 item, I didnt even know some ph1's have 2. and also there wasnt anything on there site saying to check if it has 1 or 2 lambdas. ordered off ktec...

i had one, its just a gadget

£80 instead?

I have a new pair of top mounts but havnt fitted them yet, although i really shouls as they make so much noise even over little bumps. think it will be a process of elimination: new mounts, try spacer washers, wheel bearing. if not then i'll just ignore it till it gets worse. nathan

take a look in the local meets section.

How many does a Ph1 have? I have always been told they have 1.

no car is 100% standard

Im sure I have a front O/S wheel bearing going but had a MOT the other day and told them about it but they couldnt find anything wrong... at all. its only when i turn left at speed of sharply, sounds just like a bearing, harder you turn the louder it gets. started a month ago. any other ideas...

i always thought dot 5.1 is more of a race fluid and needs to be bled more often than dot 4???

very tidy cupra!! what exhsust have you got on the clio. clios is obviously awsome too. nathan

no, i'll have a look now, lol, got a section 59 yesterday for driving spiritidly round somerby roundabout oops. Tegs in a different league tho, awsome car. 105 lol very lucky

oh, well thats me anyway, parked next to your Vee at the muddle go nowhere pub a few months back to, took a cheeky pic of them both too. nathan