Search results

I have an issue whete the vertical arm (one that leaks at the seal) in the gearbox is sticking when selecting first, second and reverse,up position at the box. Reverse is very hard, have to push the lever over and select, I've disconnected the linkage to rule that out and confirm that the arm...

I'm looking to get some winter tyres for my megane, 235/35/19. Has anyone used the kumho wintercraft wp72? They seem reasonably priced Cheers

A few months ago my eml popped on whilst going to work, it's stayed on although the car runs fine as it always has done, it's due a cambelt/plugs etc in a few weeks but is there a scanner I can use at home to see what code it is and maybe sort it, I'm guessing it's a sensor somewhere but not...

Obviously i dont have clip (think that's what it's called 🤪) so would a generic code reader be decent enough for a scan, my 172 eml came on about 5months ago when travelling to work and has stayed on, car runs as should and have noticed no difference, I'm guessing it's one of the lambda's in the...

Is there anyone who does titanium shim to fit against the inside pad on a standard caliper, it's to protect the seals on track from getting cooked so much and cracking prematurely

Not for a clio but thought I might get an answer in here 😁 Does anyone have the stock alignment settings for a megane 250/265/275cup?

Hi, I'm looking for ideas on how best to protect the back of my recaro seats in my megane, kids have battered f@kc outta my other car ones and are heavily scratched. I'm thinking of some vinyl wrap I can put on, has anyone did this before and will it be easy enough to do? Cheers

I need to replace the top mount bearings on my 172, I have the top mount/strut brace combo and believe it to be the old design. This is the bit I'm unsure off, I seen somewhere that the bearings are slightly different on the newer brace set up, does anyone know the visual differences between the...

As above, does anyone have a diagram for ECU pinout for the 172, Cheers

Looking for a bit of advice, does the pulse wire from the speed sensor on the gearbox go to the ecu then onto the clocks & head unit, think its an orange wire to the ecu then violet from the ecu onwards...does anyone have the pin locations at the ecu, I'm trying to identify if it is the sensor...

As title, is there some type if wax I can just spray on and power wash off, that will give some protection over winter,

Looking for recconended known settings, something that's just a good all rounder for both wet and dry, cars not used much on the road and only on track now in again so not to worried about tyre wear 172cup on b14's, ad08r, camber bolts & pms top mounts Thanks 👍

Looking online i can only find the ktec kit available, does anyone else offer a SC kit for the mk2 RS?

Evening All, It has come to my attention that a certain individual under the name of BLOKE / CARL WADESON who is very active on here is someone who shouldn't be trusted having ruined a guys R26 over on the Facebook page meganespoet.net resulting in his workshop being forced open to recover the...

Anyone in aberdeen/aberdeenshire got clip that could permanently turn off my airbags for some cash?

Anyone got any info on fitting/or has fitted a 172/182 head to a meg 225 block, is there any modifications required on the cambelt side? just looking at options prior to conversion Thanks

Im planning to carry out a meg 225 engine & box conversion into my 172cup, i have a complete donor car but have a few questions: Whats the best way to to go with management so everything still works as it should, in regards to the speedo etc? Also is the only way around the servo issue to fit...

Evening all, Looking to go ahead with boost on my 172 as it simply does not have enough grunt unless you drive it hard, was looking at low boost then the plan is to fit a complete megane set up once money/time allows but may be a few years away (babies/houses are my main issues :( knowing quite...

Afternoon, When fitting a 225 eng & box in to a 172, would the downpipe for a turbo conversion kit from ED fit? or best to get one custom made, i shall be using the standard servo? also who does everyone use to get their custom shafts made, looking for a tried and tested supplier Thanks again Nick

Hi, Anyone know the correct bulb types for a Clio 172 cup, I need sidelights, main and full beam, Thanks

Don't know what is the best section to put this under, but does anyone have a list of the sizes of bolts required for the front wishbone, strut to carrier, rear axle etc? Basically I am looking to replace all bolts when I rebuild the underside of my 172cup, and maybe have them plated also to...

Hi, Once I finally get round to modifying the cup, one thing im looking to do is relocate the battery behind the passengers seat to free up some space under the bonnet for future modifications, i will be using the car on the road as well as the track so looking to go with the smallest standard...

Hi, Thought i would put this on here to see if anyone has either had this problem or could help diagnose what could be wrong, the problem is with my 2010 bmw 320d, basically it keeps pulling to the left, its only on 40k, fsh, tyre pressures are all ok, no buckled wheels, tyre wear is...

Evening, I will be replacing every part of my suspension/brakes later this year, but was wondering what is the best way to protect everything from future corrosion, i know its going to happen as time goes on but thought im best to try and protect what i can prior to fitting all the new parts. I...

as title, where's best to buy a 4 point harness for road use but using the aircraft style fastener Thanks

as above, where's the best place to buy new front Clio 172 cup calipers, was going to rebuild my own ones but thought I'd check the cost of new ones first, I don't want reconditioned ones Thanks

as above does anyone have these fitted? there is a set i am going to go and look at tomorrow second hand, but seen a few people saying they are uncomfortable, are they that bad? Thanks

anyone ever used black diamond predator pads on track, also looking at wezmoto brake lines, again anyone any dealings with them?

Hi, I've just purchased a set of 15 inch wheels for the track and I'm sure they'll fit but thought best to ask the people who'd know, there 6.5 x 15, 4x100, et 38 with a bore of 60.1 with spigots fitted, other thing is does anyone know where to buy aluminium spigots rings OD 73.1 to 60.1...

As above, where do you guys but parts such as powerflex bushes,steering wheels boss,seats,suspension etc,etc?:S