Tie Rod Removal tool?

Andyrg@ ClioTurbo · Jul 23, 2012

Chaps.

Do Renault supply a tool to remove the tie rods ( Drum sticks ) off a clio 172, its certainly not a job for the masshoove 32mm spanner i have as its a little tight in there, or what do you use? as i resulted to mole grips!

Andy

Budgie · Jul 23, 2012

32mm Crows foot. Bit grinded off to make it thinner.

Either that, or a 32mm viscous fan spanner bent to shape might work? Not sure how tight they have to go?

JackJack · Jul 23, 2012

Fred@BTM made his own custom tool to do the job.

bmh.01 · Jul 23, 2012

Camlock tools work great.

Dan519 · Jul 23, 2012

I use an old machinsts spanner for adjusting mills and lathes. Perfect size, and cut from a flat piece of steel so nice and thin.

Chip-mk1 · Jul 23, 2012

I use a tie rod removal tool, it slides over the tie rod and has a cammed action inside it (like a stud remover) to allow it to bite onto the tie rod.

Takes literally a few seconds, you just slide it on and undo it with an impact gun.

Andyrg@ ClioTurbo · Jul 24, 2012

i managed to get them back on with a open ended 32 with the end ground thing, just thought there may be a tool to do it, i like tools! and like doing things correctly, i was tempted to bent the spanner but its a 32mm snap on puppy and dont think it would bent to easy lol

Chip-mk1 · Jul 24, 2012

This is the type of tool I use:

http://www.ldemporium.co.uk/images/BER61021.jpg

You just slide it up the track rod, and then undo it either using a spanner on the hex section or a impact gun in the 1/2 inch sqaure hole in the end of it.

JackJack · Jul 24, 2012

Looks good Chip.

Jonff · Jul 24, 2012

I used this to remove them lol.

Tool chip has posted is the proper tool for the job but they're expensive and not worth buying unless you're regularly using it IMO.

Andyrg@ ClioTurbo · Jul 24, 2012

jonff your my new special p**n tool friend

i will purchase one of them ends asap

Budgie · Jul 24, 2012

Budgie said:
32mm Crows foot. Bit grinded off to make it thinner.

Either that, or a 32mm viscous fan spanner bent to shape might work? Not sure how tight they have to go?

Jonff said:
I used this to remove them lol.

Tool chip has posted is the proper tool for the job but they're expensive and not worth buying unless you're regularly using it IMO.

Andyrg said:
jonff your my new special p**n tool friend i will purchase one of them ends asap

Aheeeem.

Andyrg@ ClioTurbo · Jul 24, 2012

Budgie said:
Aheeeem.

LOL Sorry Buddie but p**n is just no good with out photos

LOL

Bren Rogers · Mar 18, 2013

Been trying to find such a tool at a decent price, as I only really need to use it once. Everywhere offering 32mm crowfoots wanted around £35.

Found this little bargain on ebay. Yet to see the quality, but shall be delivered next week, so will see how it goes.

http://www.ebay.co.uk/itm/230908128489?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649

antoenail1 · Nov 28, 2013

Bren Rogers said:
Been trying to find such a tool at a decent price, as I only really need to use it once. Everywhere offering 32mm crowfoots wanted around £35.

Found this little bargain on ebay. Yet to see the quality, but shall be delivered next week, so will see how it goes.

http://www.ebay.co.uk/itm/230908128489?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649

Did this tool work for you? Looking for a tool to do mine?

Fred@BTM · Nov 28, 2013

no chance will that fit

AlexW · Nov 28, 2013

I have a viscous fan spanner for this very reason, Still can't get in there that well, but works good enough! Can get them for about £8 too.

MicKPM · Nov 28, 2013

I use this...

Rob669 · Nov 28, 2013

I've got the one that Chip-mk1 posted up, but I thought you were also supposed to use something to hold the rack at the same time?

Anyways, it worked on mine with no fluid loss and has been fine since.

Mike@Rentech · Nov 28, 2013

The Burgen tools one works a treat, i have the very same one.

f0xy · Nov 28, 2013

antoenail1 said:
Did this tool work for you? Looking for a tool to do mine?

it worked yes

chipchip2010 · Nov 28, 2013

Done mine last week used mole grips and a bar not easy way of doing it but at least it didn't cost me anything

car.crash · Nov 28, 2013

http://www.amazon.co.uk/gp/product/B006B3OKCY/?tag=cliospnet01-21
Have done mine twice using this tool.
plenty of room and works a treat, ideally a few extension bars will make it easier for you.

Laine_16v · Nov 29, 2013

I used a ratcheting crows foot, although had to file down the purple plastic stops slightly as the tool width was too big, not a proper method, but it worked perfectly and the tool was cheap (ill probably never use it again).

stokie4ker · Nov 30, 2013

How about using a 32mm box spanner like this?

Slide it down the rod and use an adjustable spanner or pipe grips on the outside of the 27mm end.
Or am I missing something?

Flat Eric · Nov 30, 2013

Plumbers tools! ^^^^^
They slip tight nuts on basin taps so I doubt they'll be much use. Worth a try though

Dan@SJM · Nov 30, 2013

Just use the proper tools for the job. I have the Bergen tie rod removal tool also, slides over, 1/2" ratchet and undo. No fuss, no getting stuck etc.

car.crash · Nov 30, 2013

The thing with the crows foot is some of the ones I've removed and refitted have no flats for a spanner so you need the Bergen type tool anyway.

Ianboom · Nov 30, 2013

I've got the bergen tool, i bought it to do my old 182, it's since been used on a Trophy and my 200 so starting to pat fot itself.

Anybody near Solihull wants to borrow it, drop me a pm.

Ian.

antoenail1 · Nov 30, 2013

Thanks for your replies lads! I'll sort it now!

antoenail1 · Dec 1, 2013

car.crash said:
http://www.amazon.co.uk/gp/product/B006B3OKCY/?tag=cliospnet01-21
Have done mine twice using this tool.
plenty of room and works a treat, ideally a few extension bars will make it easier for you.

i thought the tie rods were 32mm this tool is 33mm minimum?

antoenail1 · Dec 1, 2013

antoenail1 said:
i thought the tie rods were 32mm this tool is 33mm minimum?

Anyone used it and can confirm it works?

Chip-mk1 · Dec 2, 2013

antoenail1 said:
i thought the tie rods were 32mm this tool is 33mm minimum?

The hex section is slimmer than the balled section that these tools go on.

antoenail1 · Dec 2, 2013

Chip-mk1 said:
The hex section is slimmer than the balled section that these tools go on.

So this should work then?

Chip-mk1 · Dec 2, 2013

Should do although I havent used that specific one personally.

kilmo_172cup · Feb 8, 2014

Can anyone confirm that this Bergen tool definitely works, as the actual tie rod is 32mm but this tool has a 33-42mm specification:

http://www.amazon.co.uk/gp/product/B006B3OKCY/?tag=cliospnet01-21

Faboka · Feb 8, 2014

I used a viscous spanner. Was fairly straight forward.

Hardest part for me was getting the rubber boots back on.

Cliof4rire · Feb 8, 2014

Hi their the sealey tie rod remover is a great tool
here the link
http://www.sealey.co.uk/PLPageBuild...rogroup=1520&analysiscode=&requiredresults=16

Ade T · Feb 8, 2014

Any special techniques/tool for removing the tie rod ends out of the hub? After you've undone the first few threads the ball joint drops and it just spins.

welshname · Feb 8, 2014

It depends if they are original or aftermarket.

On my originals I had to cut them off but there are various ways on non original ones:

If you slide the boot down a little there are two flat spots to put a spanner on to stop it spinning
Or
There is an Allen key/torx bit hole in the top
Or
The very top is hexagonal to get a spanner on

Tie Rod Removal tool?

Sing Hosanna!!

Similar threads