Search results

The rear strut brace is for sale but gives an idea of red in there with the white.

Rear right it allows me to bleed but any of the other i get an error when i try to activate the actuator. Any ideas people ?

My thermostat housing is leaking oil , you can see where its appears to be coming from. Is that normal ? I have ordered a new gasket to try fix this

Installed a replacement interior loom and rear loom as these had been chopped by previous , the immobiliser light wasnt going out and also noticed i wasnt getting engine management light coming on then off. I couldnt hear the fuel pump prime either. Swapped both looms and immobiliser light goes...

How much are front bumpers fetching these days ?

Whats the best way to get the dogbone hole aligned with the subframe ? With the dogbone bolted into gearbox case the hole is not close enough to get bolt in. I loosened off the upper engine mount to make sure its as far back but still not enough. I'm wondering if the exhaust or manifold is...

I currently have KW V2's fitted on my red track car , has anyone gone from these to a pure track car set up on BC racing coilovers ? If i did this then the V2'S would go on my other clio. My white clio shocks are non cup so original plan was to buy cup shocks front and rear and maybe some...

Should i have one of these between manifold and miktek decat pipe on a 182 ?

Any ideas what the issue could be , got my white clio build to start today but its idling at 3000 rpm. Thought it might be a vacuum leak but cant see anything obvious. Ive had my inlet manifolds powder coated put a new seal and gaskets on aswell. Tried swapping , throttle body and pedal and...

Are these the bolts into the box ? The thread looks damged so probably going to have to rethread.

Any ideas what the ring connector is by starter motor is ? Connected starter motor positive and spade connector

Which is the starter motor positive terminal ? Just trying to make the connections now , is it the long stud terminal or the short one ?

Anybody got any pics or a diagram for the routing ? Cant fully remember the route , sorted the injectors side , vvt , alternator etc. Its the side by battery and gearbox upper mount , cant rememeber if any of the loom should run between the body and the upper gerabox mount or just run over the...

Alternator plug pushes in so far but doesnt clip. I remember my iceberg connector had been cut off and directly soldered to the pin. Does everyone else have this issue ? Its a valeo alternator

Ive had to remove the wiring loom out the Red clio as expected it had been chopped and the connections for the throttle etc have gone as was 9b throttle bodies. I have 2 looms which came with white clio , one loom has been stripped abit and i remember the previous owner saying he couldnt get...

Looking to paint my roll cage liquid yellow , anyone done it with rattle cans or know of a good supplier for the paints ? Is it a base coat then a pearl lacquer ? Love the colour and probably wont ever have a car thats that colour 😂😂

Anybody have the list of parts and lengths required for what i need to install the battery in the boot ? Or does somebody already make a set to lengths and crimp etc would be ideal as i dont have the crimp tool ?

Hi , just been having a nose for gearbox oil requirements. Ive seen 75w80 elf Nfj pop up ? Is this what i need and around 3 litres per box ? Need for 2 gearboxes. Is this what people recommend or any other manufacturer ? I think ive only used elf in the past when ordered oils via renault ?

Any ideas of length this bolt is for mounting cup alternator to bracket , i have adjuster bolt , im away from home for work so need to order something to suit for the weekend

I have a dodgy ignition key barrel , assuming there are no issues installing a different one ? I have 3 sets of locks and ecu and uch modules . Aslong as the ecu and uch are matching pair ?

Any ideas where i can get the bits from to make one of these ? I dont fancy paying £38 for one ! Anybody sourced some threaded bar and the threaded spacer , eyelet . Not even sure what to call in 😂🙈🙈

Anybody know what belt length is required for cup alternator set up with Epas using standard pulleys ? Cheers Finch

I see the method appears to be to cut the original nob off ! What can be fitted in place of the original ? Ive seen some quaife style on ebay , not sure if these fit ? Probably going to fit pure motorsport on my track car but looking for something for my road car Also where do these fit ?

What type of grease do i need for this install ? Been looking on here for the spline and release bearing ? Seen somebody say dont put any on spline but what about realease bearing / fork ?

Do brembo hc discs have any markings on them to identify them ? Have a set of discs on my iceberf but unsure what they are . Also who is selling these discs cheapest ?

Im looking to fit a fresh pair of cup shocks front and rear on my build. Car will be used for fast road and maybe a wet track day ! Was tempted for a set of BC racing shocks but trying to keep costs down ! The shocks appear to have apex springs , its seems to be on the high side but no engine...

I need two inserts for the rear backbox hangers. I know poweflex do afew different colour options. Whats peoples preference ,think ive seen red and black insert , is black a hardened version ? Its for my stripped white shell build Cheers

Whats the best way to attack this ? Ive never had any luck with easy outs , probably because its a cheap set from halfords. What have people done ? Assuming im not the first to have this issue 😂😂🤫🤫

Cant remember how to remove these from the tunnel 😕 whats the best way to remove them , assuming there is some form of tab retaining them

I need to fit ABS pump and it doesnt have the cage nuts in the body for the bolts. Any ideas what part number might be for these ? Not my car but showing location