JamesBryan
ClioSport Club Member
ClioSport.net
Register a free account today to become a member!
Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!
-
When you purchase through links on our site, we may earn an affiliate commission. Read more here.
BG 182
- Thread starter Louis
- Start date
imprezaworks
ClioSport Club Member
Mk5 Golf GTI :)
That does sound very good. Does it drone atall?
Sounds amazing! Excited now.
Also just made up a mixture of Deox-c (Thanks @Gus) and put my front hubs in there. Will give them a going over in the morning with a wire brush again, then let them soak.
JamesBryan
ClioSport Club Member
Oh yeah, like a b*****d at certain rpms on the motorway. Somewhere around 75-80 mph.
JamesBryan
ClioSport Club Member
I'll just do 90
JamesBryan
ClioSport Club Member
It's probably not as bad as some exhausts, but I won't lie when someone asks does it drone.
Mine drones slightly now anyway, it's more boomy being a single backbox.
JamesBryan
ClioSport Club Member
Yeah, I wouldn't say these are boomy really.
The rasp with the rear seats folded down or removed is quality.
Much less boomy with the rear seats in place. Mine is quite boomy when the engine is under slight load on cruise going uphill etc, but fine at certain speeds on the flat. I didn't make mine to be a Grand Tourer anyway, so it's irrelevant for me.
However, sounds epic when you're on it.
However, sounds epic when you're on it.
dann2707
ClioSport Club Member
Aww cute didn't know it was single, can I grab it's number
dann2707
ClioSport Club Member
Why not, I'll be sure to look after it
I bought some used 60mm hubs that needed bearings and after advice from @Gus i soaked them in deox c.
Bearings still need pressing out but this stuff is insane! Works much quicker if kept warm too but I had it in a cold cellar.
My milltek also arrived and I gave it a wipe with brake cleaner then a quick polish.
I will be fitting this on boxing day most likely! Had to strap it in for my journey to my mum's house 😂
Bearings still need pressing out but this stuff is insane! Works much quicker if kept warm too but I had it in a cold cellar.
My milltek also arrived and I gave it a wipe with brake cleaner then a quick polish.
I will be fitting this on boxing day most likely! Had to strap it in for my journey to my mum's house 😂
Made a start on fitting some new engine and gearbox mounts. I had a receipt for a gearbox mount bought by a PO but when I removed the battery this is what I found
A standard gearbox mount. Who knows what happened to the solid one!
Rather than buying just a vibratechnic gearbox mount it made sense to buy the whole kit with dogbone, engine and gearbox mounts to refresh everything.
Whilst jacking up the car I noticed this...
That'll explain the blow then! I'm going to try weld some new tabs on otherwise it's a whole new manifold jobby which isn't what I want. Puts off fitting my milltek for the time being.
Cracked on with the engine mount and changed this
Levered the whole engine forward and loctited on the centre nut. Will be respraying everything in the summer but a quick spray of satin will do for now on the bolts to freshen up slightly!
I also removed the gearbox mount cage and spider cage to make sure the spindle nut and bolt was fully tightened.
Annoyingly a previous owner had snapped this bolt in the turret. I'll be trying to weld a nut onto the back to remove this otherwise it's drilling it all out.
This is as far as I got as it came dark really quickly. One of the negatives of working outside...
A standard gearbox mount. Who knows what happened to the solid one!
Rather than buying just a vibratechnic gearbox mount it made sense to buy the whole kit with dogbone, engine and gearbox mounts to refresh everything.
Whilst jacking up the car I noticed this...
That'll explain the blow then! I'm going to try weld some new tabs on otherwise it's a whole new manifold jobby which isn't what I want. Puts off fitting my milltek for the time being.
Cracked on with the engine mount and changed this
Levered the whole engine forward and loctited on the centre nut. Will be respraying everything in the summer but a quick spray of satin will do for now on the bolts to freshen up slightly!
I also removed the gearbox mount cage and spider cage to make sure the spindle nut and bolt was fully tightened.
Annoyingly a previous owner had snapped this bolt in the turret. I'll be trying to weld a nut onto the back to remove this otherwise it's drilling it all out.
This is as far as I got as it came dark really quickly. One of the negatives of working outside...
Gave it a much needed wash today. Shame it started raining so soon afterwards as I didn't get chance to wax it. It'll do for now.
I also touched in the scuff on the front bumper. I'll be wet sanding then machining this back but I prefer it already!
I also touched in the scuff on the front bumper. I'll be wet sanding then machining this back but I prefer it already!
imprezaworks
ClioSport Club Member
Mk5 Golf GTI :)
Nice.
In the past week I had a bit of spare time after work so decided to paint my bullets that I had previously sanded smooth.
20180120_111628 by Louis Walker, on Flickr
20180119_230132 by Louis Walker, on Flickr
Pretty happy with how they turned out, but i do kind of wish the sticker was slightly smaller but i'll see once they're on!
Whilst I had the lacquer out, i sanded back my matt cf splitter and gave it around 5 coats.
20180106_195404 by Louis Walker, on Flickr
Glossy!... Not bad for £60! Just hope I don't smash it off in a week 😅
Also managed to get my hands on a non sport climate control panel to remove the sticky one that's in place at the minute.
20180118_174646 by Louis Walker, on Flickr
Had a bit of a car day yesterday, and got round to doing sub odd jobs that i've not had chance to do in the crap weather! I went over to my brothers garage and had chance to use a ramp and work indoors which made a world of difference to productivity!
For a start I dealt with the snapped stud in the turret by grinding off the captive nut on the inside of the arch. I then just used an M8 nut and bolt with a large washer to spread out the load. Saved any messing around drilling it out. I'll grab some photos next time i'm out.
I also fitted my front bilsteins that have been sat around over winter! Upon removal of my old shocks, they were completely knackered and very much in need of replacement. Had a little bit of trouble knocking the top hat over the bilstein top strut, but a socket and hammer sorted that out :smile:
Rest went relatively smoothly, and I re-greased all the top mounts before fitting them back onto the car. No pictures of them actually on the car as my phone was low battery and all photos would have been grainy. I did adjust them to be 575/570mm, sprayed in some ACF 50 and fitted a pair of motamec covers that I bought to protect the threads after seeing how good they were on @Dr Jekyll's car.
I left the rears as the Bilsteins use a strange m9x1 top nut, which is different to the standard ones on the car! I'll be ordering some new nuts (when I can find some) then fitting the rears. Genuinely can't wait as the drive has been transformed now with the bilsteins just on the front! They're so much nicer than the knackered old shocks and cooksports, just absorbing any bumps in the road but still keeping the car planted. Steering also feels lighter (mainly noticed when parking, which is nice), but as @Niall said, this could be down to the castor/tracking being all over the place! I'll be getting it all tracked once I have my new bearings pressed in and black series wishbone bushes fitted.
I woke up to snow this morning, but having seen all the salt on my front bumper the night before I had to give it a wash! Excuse the mad camber and rake, but this will soon be sorted.
20180121_122742 by Louis Walker, on Flickr
20180121_122749 by Louis Walker, on Flickr
20180121_122757(0) by Louis Walker, on Flickr
20180121_122805 by Louis Walker, on Flickr
20180121_122704 by Louis Walker, on Flickr
20180121_122728 by Louis Walker, on Flickr
I also fitted my freshly painted centre caps after giving the inside of the disc a quick lick of paint.
20180121_122823(0) by Louis Walker, on Flickr
On the milltek front, i'm still in need of sorting out the manifold flange as it's blowing a fair bit. Mainly noticed with a full car and the engine under load! It also needs adjusting at the back... maybe a job for the warmer days 😂
20180121_122857 by Louis Walker, on Flickr
20180121_122905 by Louis Walker, on Flickr
I'll be getting the rears fitted soon, then sorting out the camber and then adjusting all the height so it's bang on. :smile::smile::smile:
20180120_111628 by Louis Walker, on Flickr
20180119_230132 by Louis Walker, on FlickrPretty happy with how they turned out, but i do kind of wish the sticker was slightly smaller but i'll see once they're on!
Whilst I had the lacquer out, i sanded back my matt cf splitter and gave it around 5 coats.
20180106_195404 by Louis Walker, on FlickrGlossy!... Not bad for £60! Just hope I don't smash it off in a week 😅
Also managed to get my hands on a non sport climate control panel to remove the sticky one that's in place at the minute.
20180118_174646 by Louis Walker, on FlickrHad a bit of a car day yesterday, and got round to doing sub odd jobs that i've not had chance to do in the crap weather! I went over to my brothers garage and had chance to use a ramp and work indoors which made a world of difference to productivity!
For a start I dealt with the snapped stud in the turret by grinding off the captive nut on the inside of the arch. I then just used an M8 nut and bolt with a large washer to spread out the load. Saved any messing around drilling it out. I'll grab some photos next time i'm out.
I also fitted my front bilsteins that have been sat around over winter! Upon removal of my old shocks, they were completely knackered and very much in need of replacement. Had a little bit of trouble knocking the top hat over the bilstein top strut, but a socket and hammer sorted that out :smile:
Rest went relatively smoothly, and I re-greased all the top mounts before fitting them back onto the car. No pictures of them actually on the car as my phone was low battery and all photos would have been grainy. I did adjust them to be 575/570mm, sprayed in some ACF 50 and fitted a pair of motamec covers that I bought to protect the threads after seeing how good they were on @Dr Jekyll's car.
I left the rears as the Bilsteins use a strange m9x1 top nut, which is different to the standard ones on the car! I'll be ordering some new nuts (when I can find some) then fitting the rears. Genuinely can't wait as the drive has been transformed now with the bilsteins just on the front! They're so much nicer than the knackered old shocks and cooksports, just absorbing any bumps in the road but still keeping the car planted. Steering also feels lighter (mainly noticed when parking, which is nice), but as @Niall said, this could be down to the castor/tracking being all over the place! I'll be getting it all tracked once I have my new bearings pressed in and black series wishbone bushes fitted.
I woke up to snow this morning, but having seen all the salt on my front bumper the night before I had to give it a wash! Excuse the mad camber and rake, but this will soon be sorted.
20180121_122742 by Louis Walker, on Flickr
20180121_122749 by Louis Walker, on Flickr
20180121_122757(0) by Louis Walker, on Flickr
20180121_122805 by Louis Walker, on Flickr
20180121_122704 by Louis Walker, on Flickr
20180121_122728 by Louis Walker, on FlickrI also fitted my freshly painted centre caps after giving the inside of the disc a quick lick of paint.
20180121_122823(0) by Louis Walker, on FlickrOn the milltek front, i'm still in need of sorting out the manifold flange as it's blowing a fair bit. Mainly noticed with a full car and the engine under load! It also needs adjusting at the back... maybe a job for the warmer days 😂
20180121_122857 by Louis Walker, on Flickr
20180121_122905 by Louis Walker, on FlickrI'll be getting the rears fitted soon, then sorting out the camber and then adjusting all the height so it's bang on. :smile::smile::smile:
Jekyll
ClioSport Club Member
Lovely stuff my man :up:
imprezaworks
ClioSport Club Member
Mk5 Golf GTI :)
Tidy
Cheers mate, 2118s do look the best
Jekyll
ClioSport Club Member
Don't worry mate. He's just jealous because he's had his BG long time and doesn't do anything to it :wink:
Last edited:
🙈 Still loooads to do to this!
leeds2592
ClioSport Club Member
Bean 182 + E70 X5
Oooooo, meow.
Jekyll
ClioSport Club Member
I'm sure he'll pipe up soon.
With an agreement!
With an agreement!
Couldn't be more wrong. It's not BG any more it's more a matt brown now. And you need turini's ftw, all of clio world knows that so don't bother trying to argue the fact. [emoji12]
Clio RS
Nope, front and rear
Clio RS
so when you putting out the spacers outside, so the seat is crooked or isnt it?
Eh? Why would the seat be crooked? It's just 4 spacers, 4 bolts.
Clio RS
So there are spacers outside and inside. Each Bolt has one?
I have to reinstall my seats and im not shure if there are also spacers in the two (4) holes in midle of the car for both seats.
Sorry for the question.
I have to reinstall my seats and im not shure if there are also spacers in the two (4) holes in midle of the car for both seats.
Sorry for the question.
Yeah spacers inside and outside of each seat. 4 per seat.
Clio RS
Top! Tanks Louis!
